Registro de parámetros de impresión

Registro de parámetros de impresión

ESTADO: primeros intentos (solo idea, primeros intentos, parado, a gogo, refinamiento, acabado)

Miembros: Javier_Grana ...

Objetivo

1. Almacenar en base de datos aquellos parámetros bajo los que cada impresora funciona correctamente.

2. Hacer estadística de los valores y ajustes más habituales y productivos como velocidades y temperaturas.

3. Explotar los datos para obtener curvas de comportamiento características de cada componente.

Motivación

Conocer los settings estándar de cada tipo de máquina y componente.

Antecedentes

hay alguien que haya hecho algo parecido ya? No lo se

Métodos y técnicas utilizadas

Formulario WEB conectado. Integración con CURA o al log del SERIAL...

Detalles

Formulario prueba (ojo, mezcla catálogo problemas con registro settings): Registro de Calidad de Impresión

Ejemplo de todos los parámetros que utiliza CURA 14.03:

[profile] layer_height = 0.3 wall_thickness = 1.0 retraction_enable = True solid_layer_thickness = 0.9 fill_density = 30 nozzle_size = 0.5 print_speed = 40 print_temperature = 0 print_temperature2 = 0 print_temperature3 = 0 print_temperature4 = 0 print_bed_temperature = 0 support = None platform_adhesion = None support_dual_extrusion = Both wipe_tower = False wipe_tower_volume = 15 ooze_shield = False filament_diameter = 1.75 filament_diameter2 = 0 filament_diameter3 = 0 filament_diameter4 = 0 filament_flow = 120 retraction_speed = 50 retraction_amount = 3.2 retraction_dual_amount = 16.5 retraction_min_travel = 1.5 retraction_combing = True retraction_minimal_extrusion = 0.02 retraction_hop = 1 bottom_thickness = 0.6 object_sink = 0.0 overlap_dual = 0.15 travel_speed = 100 bottom_layer_speed = 30 infill_speed = 50 inset0_speed = 0.0 insetx_speed = 0.0 cool_min_layer_time = 5 fan_enabled = True skirt_line_count = 1 skirt_gap = 3.0 skirt_minimal_length = 150.0 fan_full_height = 0.9 fan_speed = 0 fan_speed_max = 30 cool_min_feedrate = 10 cool_head_lift = True solid_top = True solid_bottom = True fill_overlap = 15 support_type = Grid support_angle = 60 support_fill_rate = 15 support_xy_distance = 0.7 support_z_distance = 0.15 spiralize = False brim_line_count = 15 raft_margin = 5 raft_line_spacing = 1.0 raft_base_thickness = 0.3 raft_base_linewidth = 0.7 raft_interface_thickness = 0.2 raft_interface_linewidth = 0.2 fix_horrible_union_all_type_a = True fix_horrible_union_all_type_b = False fix_horrible_use_open_bits = False fix_horrible_extensive_stitching = False plugin_config = object_center_x = -1 object_center_y = -1

[alterations] start.gcode = ;Sliced at: {day} {date} {time} ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} ;Print time: {print_time} ;Filament used: {filament_amount}m {filament_weight}g ;Filament cost: {filament_cost} ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line ;M109 S{print_temperature} ;Uncomment to add your own temperature line G21  ;metric values G90  ;absolute positioning M107  ;start with the fan off G28  ;move to endstops G92 E0  ;zero the extruded length G1 F200 E3  ;extrude 3mm of feed stock G92 E0  ;zero the extruded length again G1 F{travel_speed} ;Put printing message on LCD screen M117 Printing... end.gcode = ;End GCode M104 S0  ;extruder heater off M140 S0  ;heated bed heater off (if you have it) G91  ;relative positioning G1 E-1 F300  ;retract the filament a bit before lifting the nozzle, to release some of the pressure G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more G28  ;move to endstops M84  ;steppers off G90  ;absolute positioning start2.gcode = ;Sliced at: {day} {date} {time} ;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density} ;Print time: {print_time} ;Filament used: {filament_amount}m {filament_weight}g ;Filament cost: {filament_cost} ;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line ;M104 S{print_temperature} ;Uncomment to add your own temperature line ;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line ;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line G21  ;metric values G90  ;absolute positioning M107  ;start with the fan off G28  ;move to endstops T1  ;Switch to the 2nd extruder G92 E0  ;zero the extruded length G1 F200 E10  ;extrude 10mm of feed stock G92 E0  ;zero the extruded length again G1 F200 E-{retraction_dual_amount} T0  ;Switch to the first extruder G92 E0  ;zero the extruded length G1 F200 E10  ;extrude 10mm of feed stock G92 E0  ;zero the extruded length again G1 F{travel_speed} ;Put printing message on LCD screen M117 Printing... end2.gcode = ;End GCode M104 T0 S0  ;extruder heater off M104 T1 S0  ;extruder heater off M140 S0  ;heated bed heater off (if you have it) G91  ;relative positioning G1 E-1 F300  ;retract the filament a bit before lifting the nozzle, to release some of the pressure G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more G28  ;move to endstops M84  ;steppers off G90  ;absolute positioning support_start.gcode = support_end.gcode = cool_start.gcode = cool_end.gcode = replace.csv = switchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders. G92 E0 G1 E-36 F5000 G92 E0 T{extruder} G1 X{new_x} Y{new_y} Z{new_z} F{travel_speed} G1 E36 F5000 G92 E0