Editing Imp3D-Gort
Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.
The edit can be undone.
Please check the comparison below to verify that this is what you want to do, and then save the changes below to finish undoing the edit.
Latest revision | Your text | ||
Line 1: | Line 1: | ||
{{Template:HerramientaRoja}} | {{Template:HerramientaRoja}} | ||
− | |||
− | |||
− | |||
= Información de seguridad = | = Información de seguridad = | ||
Revisar la información de seguridad general referente a impresoras 3D en [[Equipamiento/Impresora3D|Impresoras 3D]] | Revisar la información de seguridad general referente a impresoras 3D en [[Equipamiento/Impresora3D|Impresoras 3D]] | ||
− | + | ||
− | + | ||
= Precauciones específicas = | = Precauciones específicas = | ||
− | * '''El pin 14 no funciona'''. Si se cambia el firmware hay que tener en cuenta que en pins.h (en Marlin) hay que hacer | + | * '''El pin 14 no funciona'''. Si se cambia el firmware hay que tener en cuenta que en pins.h (en Marlin) hay que hacer esta modificación: |
+ | #define TEMP_0_PIN 13 // ANALOG NUMBERING | ||
+ | //#define TEMP_1_PIN 15 // ANALOG NUMBERING | ||
+ | #define TEMP_1_PIN 14 // ANALOG NUMBERING | ||
+ | #define TEMP_2_PIN -1 // ANALOG NUMBERING | ||
+ | #define HEATER_BED_PIN 8 // BED | ||
+ | //#define TEMP_BED_PIN 14 // ANALOG NUMBERING | ||
+ | #define TEMP_BED_PIN 15 // ANALOG NUMBERING | ||
+ | |||
+ | en pins.h en la sección: | ||
+ | /**************************************************************************************** | ||
+ | * Arduino Mega pin assignment | ||
+ | * | ||
+ | ****************************************************************************************/ | ||
+ | #if MOTHERBOARD == 3 || MOTHERBOARD == 33 || MOTHERBOARD == 34 | ||
+ | #define KNOWN_BOARD 1 | ||
= Especificaciones = | = Especificaciones = | ||
− | == Ficha [http://www.reprap.org/wiki/Clone_wars:Impresora_Gort/es Clone Wars]== | + | == Ficha [http://www.reprap.org/wiki/Clone_wars:Impresora_Gort/es|Clone Wars]== |
− | * '''Nombre''': | + | * '''Nombre''': '''GORT''' |
− | * '''Tipo''': [http://www.reprap.org/wiki/Prusa_i3 | + | * '''Tipo''': [[http://www.reprap.org/wiki/Prusa_i3 | Prusa i3]] en concreto [[Clone wars: Prusa iteración 3 single frame]] |
* '''Electrónica''': [http://arduino.cc/en/Main/ArduinoBoardMega2560 Arduino Mega 2560] + [http://reprap.org/wiki/RAMPS_1.4 RAMPS 1.4] | * '''Electrónica''': [http://arduino.cc/en/Main/ArduinoBoardMega2560 Arduino Mega 2560] + [http://reprap.org/wiki/RAMPS_1.4 RAMPS 1.4] | ||
* '''Extrusor''': [http://www.thingiverse.com/thing:135799 Greg's Wade extruder for Prusa i3 redux] | * '''Extrusor''': [http://www.thingiverse.com/thing:135799 Greg's Wade extruder for Prusa i3 redux] | ||
− | * '''Hot-End''': [ | + | * '''Hot-End''': [[J_Head_Hispania]] |
− | * '''Firmware''': [ | + | * '''Firmware''': [[Marlin]] |
* '''Nacimiento''': 3/04/2013 | * '''Nacimiento''': 3/04/2013 | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− |